The embedded network specialist
+31-40-2301.922

CAN-CR110/FO, CAN / CAN FD Fiber Optic Repeater

CAN / CAN FD repeater with screw terminals and fiber optic connector

The CAN-CR110/FO is used for galvanic isolation of two segments of a CAN / CAN FD network. As a special feature, the repeater separates a defective segment from the rest of the network, allowing the remaining network to continue working. After the fault has been eliminated, the segment is automatically switched back to the network.
The galvanic isolation is provided for the CAN / CAN FD segments as well as for the power supply.
Ixxat CAN-CR110/FO
Ixxat CAN-CR110/FO
Ixxat CAN-CR110/FO

Features and Benefits

  • Fiber optic enables transmission in areas with high electromagnetic disturbances
  • CAN and CAN FD interfaces in one device
  • Cost savings due to simple wiring
  • Increased system reliability
  • Almost no influence on real-time behavior
Technical data
Display Transmit and defective segment (two duo LEDs, one for each segment), Power (one LED)
CAN bus interface ISO 11898-2 with CAN choke. Two screw terminals.
Available with and without integrated CAN termination.
CAN baudrate Up to 888 kbit/s
CAN FD bus interface ISO CAN FD and nonISO CAN FD
CAN FD baudrate 500 kbit/s (arbitration bitrate) and up to 2 Mbit/s  (flexible data rate)
Delay typ. 300 ns (corresponds to ~60 m bus length;between the wire connection of a FO Repeater through the fiber optic cable to the wire connection of a second FO Repeater (not including the signal delay time of the fiber optics, which is ~5 ns/m)
FO transmitter Broadcom HFBR 1404Z, 820 nm
FO receiver Broadcom HFBR 2402Z, 820 nm
FO line  Multi-mode fiber optic line (only glass)recommended 50/125 µm, 62,5/125 µm, also compatible with 100/140 µm, 200 µm (pay attention to max. line length)
Max. line length between two FO repeaters 50/125 µm = 1500 m, 62,5/125 µm = 2000 m
Power supply 9-36 V DC, typ. 70 mA, max. 100 mA, through terminals
Galvanic isolation 1 kV DC / 1 sec, 500 V AC / 1 min; CAN 1, CAN 2 and
power supply are galvanically isolated from each other.
Certification CE, FCC
Temperature range -20 ºC ... +70 ºC
Housing, size Plastic enclosure, 22.5 x 105 x 114 mm
Contents of delivery
- CAN-CR110/FO
- User Manual

Part number(s)

1.01.0210.11020
CAN-CR110/FO, 1x CAN / CAN FD with Galvanic Isolation, 1x FO
with bus termination resistor
CAN-CR110/FO, 1x CAN / CAN FD with Galvanic Isolation, 1x FOwith bus termination resistor
1.01.0210.11220
CAN-CR110/FO, 1x CAN / CAN FD with Galvanic Isolation, 1x FO
without bus termination resistor
CAN-CR110/FO, 1x CAN / CAN FD with Galvanic Isolation, 1x FOwithout bus termination resistor

Getting interested?

Are you interested in the CAN-CR110/FO, CAN / CAN FD Fiber Optic Repeater? Please request, without any obligation, for a quote. Would you like more information? Please send an email to or visit our contact page.
You can call us if you like, we can be reached at +31-40-2301.922. We are pleased to help you and do offer you practical advice and support.

Related products

  • CAN-CR100

    CAN / CAN FD repeater with screw terminals

  • CAN-CR120/HV

    CAN / CAN FD repeater with screw terminals and 3 kV galvanic isolation

  • CAN-CR200

    Modular ISO 11898-2 CAN Repeater with backbone bus

  • CAN-CR210/FO

    Converter from ISO 11898 CAN to fiber optic cable with hub

  • CAN-CR220

    ISO 11898-2 CAN Repeater with 4 kV galvanic isolation

PC CAN-interfaces
CAN Bridges & Gateways
Communicator CAN
CANopen X-gateway
CANopen PLC-extentions
canAnalyser 3 Suite
CAN Diagnostic Tools
CANopen Software
CAN Accessories